Using Spectral Blurring to Assess Effects of Channel Interaction on Speech-in-Noise Perception with Cochlear Implants

Twelve post- and peri-lingually deafened, native speakers of British English took part. Half of them were female and their mean age was 67 years, with a range from 49 to 76 years. Subjects were unilaterally implanted users of an Advanced Bionics (“AB”; Valencia, CA, USA) HiRes 90K™ cochlear implant and had at least 3 years of experience with their device with a mean duration of implant use of 5.8 years. Only the implanted ear of each subject was used for the presentation of stimuli. If a subject was wearing a hearing aid in the other ear, then it was taken off during the experiment. Prior to the experiment, the most recent clinical MAP was obtained for each subject. Details about the demographic information and devices used by the subjects are given in Table 1. The study was approved by the National Research Ethics committee for the East of England. Subjects gave their informed consent and were paid for taking part and reimbursed for travel expenses. All twelve subjects took part in experiment 1 (“Experiment 1: Blurring at the Input Level”) out of which eight took also part in experiment 2 (“Experiment 2: Blurring at the Output Level”) several months later.

Speech-in-noise (SIN) performance was tested following the procedure described by MacLeod and Summerfield (1990). Sentence lists from the BKB corpus (Bench et al. 1979) spoken by a British male talker were mixed with time-reversed speech from the Harvard sentences (Rothauser 1969) spoken by a different British male talker. This background noise contained the highly modulated characteristics of competing speech, as it occurs in realistic listening environments, but reduced informational masking with the use of an unintelligible masker (Deeks and Carlyon 2004). Furthermore, the use of a competing talker as masker has been suggested to be more sensitive to differences in spectral resolution by CI users than other masker types such as stationary speech-shaped noise (Croghan and Smith 2018). An adaptive one-up/one-down procedure was used to measure the speech reception threshold (SRT) at which 50 % of the sentences were understood correctly. The initial signal-to-noise ratio (SNR) was set to 4 dB SNR, and increased by 2 dB per trial, while repeating a randomly drawn sentence from the list, until the subject repeated the three keywords correctly. The adaptive procedure adjusted the SNR with a fixed step size of 2 dB until all 15 sentences of that list had been presented. A trial was deemed correct if all three keywords of that sentence were correctly repeated by the subject and the final SRT score for that run was calculated as the average of the last ten SNRs presented.

Each subject’s spectro-temporal acuity was evaluated using the Spectro-Temporal Ripple for Investigating Processor EffectivenesS test (STRIPES, Archer-Boyd et al. 2018). The STRIPES test uses an adaptive procedure to measure the threshold at which the subject can just distinguish the target stimulus from two reference stimuli in a three-interval, two-alternative forced-choice task. Stimuli consisted of 1-s-long, concurrent exponential sine sweeps moving up or down in frequency from 250 to 8000 Hz. The subject had to select the target interval, which was either the first or last interval, and which was always an upward sweep; the other two intervals contained downward sweeps. The number of concurrent frequency sweeps (the “density”) is varied to titrate difficulty, with the task being very easy at a density close to 1, and progressively harder at higher densities. The starting frequency was roved across trials and the beginning and end of each interval was masked by short noise bursts to reduce the salience of onset and offset cues. An adaptive two-up/one-down procedure started with a sweep density of 1.1 and adjusted the density per trial with a density step size of 0.5 (for the first 4 reversals) and 0.2 (for the last eight reversals). (A non-integer density can occur, when, in this example, 2 stripes are present during 10 % of the time and 1 stripes is present 10 % of the time; see Archer-Boyd et al. (2018) for details.) The test was complete after 12 reversals and the final score of the run was calculated as the average of the last four reversals. Each subject performed three runs of the STRIPES test with the experimental MAP that was most similar to their clinical MAP and their STRIPES score was calculated as the average of those three scores. The STRIPES test takes about 5–10 min per run, leading to a total of about 30 min of testing per subject.

The experiment took place in a sound-attenuated testing room. Testing stimuli for the SIN and STRIPES tests were presented with a laboratory owned programmable Harmony CI speech processor (Advanced Bionics, US) that was worn by the subjects during the testing. Stimuli were generated in MATLAB (Mathworks, US) using a battery-powered laptop computer (Dell XPS15, Windows 10 Pro) that was connected via an external soundcard (Roland UA-55) and an audio cable to the auxiliary input of the CI speech processor. For each subject and at the beginning of each SIN testing session, the presentation level was set by adjusting the manual volume control of the soundcard to a “comfortable level” for each subject (level 6 on the loudness scale provided by Advanced Bionics) using a sentence from the Harvard lists. All SIN stimuli were calibrated to the same RMS level as the stimuli used to set the presentation level and the presentation level was kept the same for all MAPs under test. For safety reasons and to confirm equal loudness between MAPs, subjects were asked during the testing if the presentation level was comfortable to them for each of the different MAPs and this was confirmed by all subjects and for all MAPs.

For the first experiment, we varied the amount of blurring, as a means of manipulating channel interaction, by adjusting the spectral overlap between electrode channels in terms of the acoustic bandwidths of the input analysis filters. This method of blurring at the input of the CI has been used previously and led to significant decreases in performance on a spectro-temporal test with CI users (Archer-Boyd et al. 2018). The Advanced Bionics (AB) CI speech processor uses a 16-band analysis filter bank with a frequency range from 238 up to 8054 Hz. The filter bank channels are constructed by combining sets of output bins obtained from an FFT analysis stage and do not normally overlap with adjacent channels in the standard clinical MAP. Using the standard clinical MAP for each subject as starting point, we generated a set of experimental MAPs per subject by changing the lower and upper cut-off frequencies of the individual filter bank channels (using BEPS+ software from AB), thereby decreasing or increasing the spectral overlap between adjacent channels. The centre frequencies of the filter channels were kept roughly constant between all MAPs, and only the bandwidths of the “blurred” channels were multiplied by a factor of 0.5, 2, 3, 4, 6 or 8 (Table 2). This led, for example in the case of a blurring factor of 8, to filter bandwidths that were 8-fold wider than in the standard clinical MAP. We compensated for the change in filter bandwidth by applying a correction gain for each filter channel to compensate for changes in loudness. This gain was calculated as ten times the base-10 logarithm of the ratio of the blurred and original bandwidths in Hz. Six different blurring factors were used to generate 12 experimental MAPs in total. Half of those were generated by applying the spectral blurring to all 15 active electrode channels (condition “ALL-15-Input”, shown in Fig. 1) and half were generated by blurring 5-of-15 active electrode channels (condition “5-of-15-Input”) that were distributed evenly along the array with a spacing of 3 electrodes. For the 5-of-15-Input condition, we changed the filter bandwidths of only five electrodes, either electrodes 2,5,8,11,14 or electrodes 3,6,9,12,15, to the same as used in the ALL-15-Input conditions with the remaining electrodes kept similar as for M1 or the clinical MAP. The two 5-of-15-Input electrode selections were equally split between subjects. In the following, the MAP most similar to the clinical MAP is noted as “M1” and the experimental MAPs are noted as “M05, M2, M3, M4, M6, M8”, for the ALL-15-Input condition, and “M05b, M2b, M3b, M4b, M6b, M8b”, for the 5-of-15-Input condition, whereas the MAP number directly reflects the blurring factor used in that MAP.

It should be noted that electrode 16 was deactivated for all subjects in this experiment to make the experimental MAPs as similar as possible across subjects. We also never used electrodes that were deactivated in the subject’s clinical MAP, which affected only subject S11 with electrode 8. For S11, this led to a gap in the stimulation pattern of all test conditions due to electrode 8 being disabled. We used electrodes 3,6,9,12,15 for the 5-of-15-Input condition with S11 to keep the same number of five manipulated channels as for the other subjects. Furthermore, the processing strategy was changed to HiRes-S for all subjects (similar to continuous interleaved sampling, CIS, without current steering or noise reduction functions active as compared to their clinical MAP). The same pulse rate and pulse width was used between the different experimental MAPs but differed between subjects depending on their clinical settings.

Experiment 1 was split into two 3-h sessions per subject that were performed on two different days. In the first session, subjects completed the SIN test first with five MAPs from the ALL-15-Input condition (M05, M1, M2, M3, M4) in random order and second with five MAPs from the 5-of-15-Input condition (M05b, M1b, M2b, M3b, M4b) in random order. For each MAP and before the SIN test, subjects were presented with one randomly chosen list (10 sentences) from the Harvard sentences and were able to read along to acclimatize to that MAP. The SIN test was then performed twice per MAP and the average of the two runs was taken as the final SRT for that MAP. In the second session, subjects were tested with three MAPs from the ALL-15-Input conditions (M4, M6, M8) in random order and then with three MAPs from the 5-of-15-Input condition (M4b, M6b, M8b) in random order. The same procedure as in the first session was followed. The scores from the two sessions were used together for the analysis, with the score for M4 and M4b (which were tested in both sessions) calculated as the average between the two sessions. After the SIN testing was complete, subjects performed three runs of the STRIPES test with M1 and the average was taken as their final STRIPES score.

Group average scores for the SIN test with blurring at the input level are shown in Fig. 2 for the ALL-15-Input and the 5-of-15-Input conditions. The effect of blurring was evaluated using one-way repeated-measures ANOVAs with the factor MAP for each condition. For the ALL-15-Input condition, there was a significant main effect of MAP [F(6,66) = 19.68, p < 0.001]. Pairwise comparisons using Tukey’s honest significance test revealed significant differences for the comparisons M05 vs M3 (Diff = 1.7 dB, t = −3.19, p < 0.05), M05 vs M4 (Diff = 2.1 dB, t = −3.81, p < 0.01), M05 vs M6 (Diff = 3.4 dB, t = −3.83, p < 0.01) and M05 vs M8 (Diff = 7.5 dB, t = −7.1, p < 0.01); for M1 vs M4 (Diff = 1.7 dB, t = −3.42, p < 0.05) and M1 vs M8 (Diff = 7.1 dB, t = −6.63, p < 0.01); for M2 vs M6 (Diff = 2.7 dB, t = −3.17, p < 0.05) and M2 vs M8 (Diff = 6.7 dB, t = −6.73, p < 0.01); for M3 vs M8 (Diff = 5.8 dB, t = −5.67, p < 0.01); and for M6 vs M8 (Diff = 4.1 dB, t = −4.4, p < 0.01). These differences in SRTs were close to or substantially larger than 2 dB which is considered a clinically relevant difference for the speech-in-noise test used here. For the 5-of-15-Input condition, there was no significant main effect of MAP [F(6,66) = 0.72, p = 0.634].

The individual SIN scores for the twelve subjects and all MAPs are shown in Fig. 3 for the ALL-15-Input condition. A segmented linear regression with two segments was fitted using the “fit” function provided by MATLAB (Mathworks, US). The first segment was restricted to very small slope values in the range [− 0.1, 0.1] (change in SRT per blurring factor) and the second segment was restricted to positive slopes in the range [0, 20]. There were no further restrictions applied and the same settings were used for all subjects. The knee points of the two segments were considered the threshold at which spectral blurring affected speech-in-noise perception at the subject level. Knee points varied markedly between subjects and ranged from a spectral blurring factor of 2 for S11 up to 8 for S2 (the maximum value possible), with the other subjects in between these extremes. Interestingly, subject S2 showed no detrimental effect of spectral blurring for any MAP, but all other subjects had knee points smaller than 8. There was a positive relationship between spectral blurring knee points and SIN performance with M1 across subjects (r = 0.63, df = 10, p = 0.029), meaning that subjects with better SIN performance (lower score) with a MAP that was most similar to their everyday setting were more affected by spectral blurring (lower knee point) than subjects with worse SIN performance. This correlation was of similar size and significant even when the SRT with M1 was excluded from the calculation of the blurring knee points. Table 3 shows the performance scores with M1 for the SIN test and the spectral blurring knee points for all subjects. We also calculated the knee points for the 5-of-15-Input condition but only subject S6 had a knee point lower than the maximum which was similar to the one for the ALL-15-Input condition (M3). We conclude that, overall, the blurring knee points confirmed the absence of an effect of blurring on SIN performance with the 5-of-15-Input condition.

The results from the spectro-temporal test STRIPES are also shown in Table 3 together with the SIN M1 scores and the spectral blurring knee points. STRIPES scores varied across subjects over a range of densities from 3.4 up to 7.6 with a mean score of 5. There was a significant negative relationship between spectral blurring knee points and STRIPES scores across subjects in the predicted direction (Spearman’s rho = −0.61, df = 10, p = 0.037; a non-parametric test is used because STRIPES scores were not normally distributed according to the Shapiro-Wilk test with W = 0.85, p = 0.036). Figure 4 shows this negative association and its linear regression as well as the association between blurring knee points and SIN performance with M1.

We evaluated the effect of spectral blurring at the input of the CI on SIN performance in twelve CI users by adjusting the spectral overlap between electrode channels. In line with our main hypothesis, this led to an increase in SRTs with spectral blurring for the case when all electrode channels were blurred. This effect was strongest for the most extreme blurring condition M8 and statistical tests confirmed significant differences for comparisons between the conditions using no or little blurring and the conditions using higher blurring factors.

Surprisingly, there was no effect of spectral blurring on SIN performance for the case when one-third of the electrodes were blurred, even for the most extreme case with M8b. This was unexpected in light of previous research on site-specific optimization strategies in CI users, which were based on the rationale that individual electrode channels can be adjusted to alter SIN performance and, if done correctly, should lead to improvements. Here we show that even extreme blurring, when applied to five evenly spaced channels, does not impair performance on a masked speech test. Hence, at least for the particular manipulations and speech test used here, the second of the implicit assumptions described in the Introduction is not supported; performance is not reduced with five “bad” channels, even when those channels are spectrally blurred by a factor of eight. The implications and limitations of this finding and of the results of experiment 2 are discussed further in “General Discussion”.

Across-subject performance differed markedly in the ALL-15-Input condition with some subjects being more affected by spectral blurring than others. The knee points, as a measure of how much blurring was required to degrade SIN performance in a given subject, correlated with the SIN performance across subjects when using the MAP most similar to their clinical MAP. This association may have been due to an increased interference of the competing talker noise at lower SNRs than at higher SNRs, so that subjects who tolerated higher levels of noise would have been affected more by an increased overlap between filter channels than subjects who tolerated lower levels of noise. In general, this association is in line with the assumption that channel interaction affects SIN performance on an individual basis. A further advantage of measuring the knee point is that it allows one to distinguish between the effects of spectral resolution and of more central cognitive factors, both of which can affect speech perception and which are hard to disentangle when measuring performance with a single amount of (or no) blurring. Specifically, we assume that the knee point measures the limits of the listener’s internal spectral resolution, including that produced by current spread, whereas the overall SIN performance (e.g. the SRT for condition M1) reflects both spectral resolution and more central, cognitive factors.

The STRIPES test was performed to measure spectro-temporal acuity for the twelve CI subjects to explore the second hypothesis under test: subjects with high acuity, as indicated by their STRIPES scores, would be affected more by spectral blurring than subjects with low acuity. A significant correlation was indeed found. This suggested that the STRIPES test may effectively measure spectral resolution in a way that is relevant for the perception of speech. Performance on the STRIPES score did not correlate significantly with SIN performance with the M1 map (Spearman’s rho = − 0.38, df = 10, p = 0.22), but this could be due to a lack of statistical power (Anderson et al. 2011).

We note that spectral blurring at the input level, as imposed in experiment 1, simulated only some effects of the channel interactions that may arise from channels that produce broad current spread. Specifically, in the case of a subset of electrodes being affected, we simulated to some extent the loss of information conveyed by those channels, such as might occur due to neural degeneration in the auditory nerve and more centrally. However, we did not simulate the increased neural or charge interactions that occur between an electrode that produces a broad current spread and the neighbouring channels. Nevertheless, the results do show that severely degrading the information conveyed by one-third of all available electrodes has no effect on performance, and this finding should be taken into account when designing site-selection strategies based on a small subset of distributed electrodes along the array.

For the second experiment, we varied the amount of blurring, as a means of altering channel interaction, by adjusting the number of electrodes used for the stimulation of each channel. Advanced Bionics CIs use an electrode array with up to 16 active electrode contacts for the electrical stimulation of the auditory nerve. In the standard mode as used in the clinical MAP of the subjects, either one or two electrodes are used to convey the information extracted from each of the 16 filter bank channels. A single electrode is used per filter bank channel in the CIS-like coding strategy used for the experimental MAPs (HiRes™) whereas two adjacent electrode channels, which are weighted and stimulated simultaneously to generate a virtual channel located between the two electrode channels, are used for the coding strategies that use current steering (HiRes™ Optima, HiRes™ Fidelity 120). For experiment 2, we increased the number of simultaneously stimulated electrode contacts per filter bank channel by the same factors as used for experiment 1 (with 1, 2, 3, 4, 6 and 8 simultaneous electrodes stimulated per channel for the blurring factors of 1, 2, 3, 4, 6 and 8, respectively). The same notation as in experiment 1 was used here, in which the number of the MAP indicates the blurring factor used but the conditions in experiment 2 are called “ALL-15-Output” and “5-of-15-Output” due to blurring applied at the output level of the CI. It should be noted that condition M05 was not possible here. Furthermore, while it was possible to generate those six MAPs for the 5-of-15 condition (M1b, M2b, M3b, M4b, M6b, M8b), technical reasons meant that it was not possible to generate condition M8. Therefore, only five MAPs were generated for the ALL-15-Output condition (M1, M2, M3, M4, M6). In this experiment, simultaneously stimulated electrodes were chosen so that either the middle electrode coincided with the respective filter channel (e.g. for M3 and filter channel 5, electrodes 4, 5 and 6 were used simultaneously), or they were shifted towards the basal end (e.g. for M6 and filter channel 5, electrodes 3, 4, 5, 6, 7 and 8 were used simultaneously). For all filter channels along the array, including the most basal and most apical ones, the same number of simultaneous electrodes were used (with one exception: the most basal channel in M6 used only a single electrode due to device limitations). This resulted in shifted electrode selections towards the base for the most apical electrodes (e.g. for M3 and filter channel 1, electrodes 1, 2 and 3 were used simultaneously) and shifts towards the apex for the most basal electrodes (e.g. for M3 and filter channel 15, electrodes 13, 14 and 15 were used simultaneously). The electrode selections for the MAPs used in the ALL condition are shown in Fig. 5. All other parameters of the experimental MAPs were kept the same as for M1 in experiment 1.

In addition to the experimental MAPs with blurring, we generated an experimental MAP (“Moff”) that deactivated the five electrodes that were blurred in the 5-of-15-Output MAPs. The remaining ten (or 9) electrodes that were active in Moff therefore used wider input filter bandwidths because the overall bandwidth was unchanged. Deactivating five electrodes also introduced some frequency-to-place stimulation shifts. Moff was used to compare the performance with a 10-channel MAP to the 15-channel MAPs under test, and to determine whether deactivation of the blurred channels would improve performance compared to the blurred MAPs. This condition was motivated by site-selection studies that deactivated a subset of “bad” electrodes to improve speech perception in CI users.

Experiment 2 was split into three 3-h sessions per subject that were performed on three different days. In the first session, subjects completed a loudness rating procedure in which the T- and M-levels were adjusted for the five electrodes that were blurred in the experimental MAPs in the 5-of-15-Output condition. After the five electrodes were adjusted individually, all active electrode channels were sequentially stimulated at M-level and re-adjusted to give similar loudness, if necessary. The SIN test was then performed with six MAPs from the 5-of-15 condition (M1b, M2b, M3b, M4b, M6b, M8b) and Moff (that had the five electrodes deactivated that were blurred in the other conditions) in random order following the same testing procedure as in experiment 1. In the second session, T- and M-levels were adjusted for all active electrodes in the experimental MAPs of the ALL-15-Output condition (M1, M2, M3, M4, M6). Again, after the individual adjustment of electrode T- and M-levels was completed, subjects listened to all active electrode channels sequentially and M-levels were re-adjusted if a channel was clearly different to the other ones. In the third session, the SIN test was then performed with five MAPs from the ALL-15-Output condition (M1, M2, M3, M4, M6) in random order and following the same procedure as before.

Group average scores for the SIN test with blurring at the electrode level are shown in Fig. 6 for the ALL-15-Output and the 5-of-15-Output conditions. The effect of blurring was evaluated using one-way repeated-measures ANOVAs with the factor MAP for each condition. For the ALL-15-Output condition, there was a significant main effect of MAP [F(4,28) = 6.81, p < 0.001]. Pairwise comparisons using Tukey’s honest significance test revealed significant differences for the comparisons M1 vs M4 (Diff = 3.2 dB, t = − 2.87, p < 0.05), M1 vs M6 (Diff = 3.8 dB, t = − 3.69, p < 0.01), M2 vs M4 (Diff = 3.6 dB, t = − 2.96, p < 0.05) and M2 vs M6 (Diff = 4.3 dB, t = − 3.19, p < 0.05). These differences in SRTs were all substantially larger than 2 dB and therefore considered clinically relevant effects for the speech-in-noise test used here. For the 5-of-15-Output condition, including all the blurring conditions M1b to M8b and Moff, there was no significant main effect of MAP [F(6,42) = 1.39, p = 0.242].

For this experimental part, even though there was a significant effect of blurring in the ALL-15-Output condition, no subject-wise blurring knee points could be calculated because the two-segment regression produced unstable results. This was likely due to the small number of five data points being insufficient for the fitting.

The statistical analysis with an RM-ANOVA for the 5-of-15-Output condition may not be sensitive enough to reveal a significant difference due to the small number of subjects (N = 8) and large number of comparison conditions. Figure 7 therefore shows individual results for all eight subjects for the blurred maps M1b to M8b together with Moff. It can be seen that SRTs were very similar across all conditions under test for all eight subjects. This clearly shows that there was no substantial effect on SRTs using either more blurring or the deactivation of five electrode channels in this group of subjects. Therefore, the variability between experimental conditions that can be observed in Fig. 6 is mainly due to inter-subject variability.

Spectral blurring at the output level, as introduced in experiment 2, simulated more directly the effects of channel interactions that arise from channels with broad current spread. We found highly significant effects of blurring on SRTs for the ALL-15-Output condition, with decreasing performance for higher amounts of blurring. This supports the rationale that blurring at the output level achieved the desired manipulation of current spread. There were no differences in performance between M1 and M2 which is in line with previous research reporting no differences in spread of excitation, pitch ranking and electrode discrimination between single- and dual-electrode stimulation modes (Hughes et al. 2013; Goehring et al. 2014), but there were highly significant differences between these and the blurring conditions using four or six electrodes. Hence blurring did not affect performance when using 2 electrodes but it did so when using 4 or more electrodes. This is in line with results reported by Langner et al. (2017) who found significant performance decreases in modulation detection thresholds and speech-in-noise intelligibility scores with a group of CI users for a “triplet” electrode configuration that used 6 simultaneously activated electrodes (3 pairs) spanning 12 electrode sites of the array (with 3 non-stimulated electrodes between the three stimulated pairs) over a standard sequential configuration with paired electrodes. Even though Langner et al.’s (2017) electrode configurations were different from blurring and they tried to compensate for channel interaction by introducing electrode gaps or flanks of opposite polarity, their findings provide further support that multi-electrode stimulation above 3 electrodes can lead to reduced spectral resolution and speech-in-noise performance. However, it cannot be excluded that other channel interaction effects such as temporal charge interactions in addition to the expected increase in spread of excitation were responsible for the decrease in performance seen in experiment 2.

In contrast to the findings with the ALL-15-Output condition, blurring of one-third of the available electrodes had no effect on performance. Hence extreme blurring either at the input or at the electrode stage did not degrade performance when applied to five evenly spaced electrodes or channels, even though it did degrade performance when applied to all electrodes. This unexpected result was confirmed both at the group level and at the subject level, with no subject showing a clear trend of decreased performance with more blurring in the 5-of-15-Output condition. Furthermore, the deactivation of the five channels that were used for the blurring led to comparable speech-in-noise scores as with the other maps. This is consistent with the finding by Friesen et al. (2001) that about 7–10 channels of information are sufficient for maximum speech-in-noise performance in CI users. In the Moff condition, subjects were able to successfully use the 10 remaining channels even with the reallocation of frequency information due to the deactivation of electrode channels. This is in line with a previous study using site selection where performance was similar between two 10-channel maps with frequency reallocation and the clinical-like map with 15 channels without reallocation (Goehring et al. 2019b). However, more recent evidence suggests that speech-in-noise performance may increase with more than 10 active electrode channels, and that this benefit may further depend on the particular configuration of the CI device, the type of electrode array and the coding strategy used (Croghan et al. 2017; Schvartz-Leyzac et al. 2017; Berg et al. 2019a, b). All of these studies used acute testing conditions and did not control for the bias effects of long-term acclimatization to the more clinical-like MAPs. In general, comparisons between studies are complicated by the use of somewhat different speech-in-noise tests that are likely to require different listening strategies composed of language, cognitive and spectro-temporal processing abilities to achieve maximum performance and are not designed to capture all aspects of speech perception.

For blurring at the electrode level, a fitting procedure was used for all active channels by adjusting the T- and M-levels for all MAPs and subjects. This ensured safe listening levels and optimized the dynamic range for each channel individually. This was necessary as the reduction in current to achieve appropriate T- and M-levels could not be predicted based on the number of active electrode sites. At group level, the levels for M2 were about half the current applied for M1, but this simple relationship did not hold for the higher blurring factors. Stimulation current ratios between M1 and the other MAPs were 1.9, 2.8, 3.5, 4.8, 5.8 for M2, M3, M4, M6, M8, respectively. The current ratios were similar between T- and M-levels with no differences larger than 0.1 apart from M8 for which the factors were 6 and 5.8 for T- and M-levels, respectively, showing that channel independence related to loudness was similar between T- and M-levels. This shows an interaction in terms of the channel-wise loudness with multiple electrodes different from a simple linear summation of current, as can be expected due to the overlap in excitation area between electrode channels. It supports the assumption that electrode channels are not independent and is consistent with the stronger effect of blurring with more simultaneously stimulated electrodes. The dynamic range values calculated as the difference between T- and M-level remained constant on a log scale across blurring conditions. This indicates that dynamic range was similar across conditions and can be excluded as potential reason for poorer SRTs with larger amounts of blurring. Interestingly, several subjects reported a change in pitch or perceived electrode channel when increasing the current from T- to M-level, especially for the strongest blurring conditions M6 and M8. This indicates that different neural regions were stimulated across the dynamic range and confirms the rationale behind blurring at the electrode level to excite broader or different neural regions than when using single-electrode stimulation. This never happened for the conditions using smaller number of electrodes M1 and M2.

Blurring by a factor of up to 3 did not increase SRTs, either when applied at the input (experiment 1) or electrode (experiment 2) stage, but there were highly significant effects at group level for blurring factors of 4 and higher. As shown in Fig. 8, the relationship between SRT and the amount of blurring was very similar for the two experiments at group level when blurring all fifteen channels. It is worth noting that although both manipulations were applied in the spectral/place-of excitation domain, they both also have the effect of blurring the temporal representation of the stimulus. This is illustrated in Fig. 9, which shows electrodograms in response to a chirp, for M1 and with a four-fold blurring (M4) as applied in experiments 1 and 2. Indeed, the electrodograms look quite similar for the manipulations in the two experiments, although it should be noted that in experiment 1 stimulation was always interleaved across electrodes, whereas in experiment 2 it was presented simultaneously on subsets of adjacent electrodes. This difference is not visible in Fig. 8 due to the coarse time-scale used.

The pattern of results shown in Fig. 8, where SRTs are constant up to a blurring factor of about 3, is consistent with previous studies that evaluated double-electrode stimulation in CI users and reported similar outcomes to single-electrode stimulation (Hughes et al. 2013; Goehring et al. 2014). It is also consistent with the idea that smaller amounts of blurring have no effect because they are smaller than any spread of excitation or degradation of the input signal that occurs in the listener’s CI with a standard clinical setting. This “internal” blurring could result from the current spread produced by individual electrodes, and/or degradations in the spectral representation at more central stages of the auditory system. As noted in the Introduction, this general idea, whereby sensitivity is measured as a function of the amount of external distortion, has been used in the equivalent noise method to shed light on perceptual limitations in previous research (Lu and Dosher 1998; Pelli and Farell 1999; Ihlefeld and Sanes 2015). Although the equivalent noise method differs from the approach used here in some important respects—for example by using signal-detection theory to model simple detection and discrimination tasks—both approaches have the potential to tease apart the effects of peripheral noise and more central processing efficiency. In terms of the broken-stick fits to our individual data from experiment 1 (Figs. 3 and 4a), we interpret the knee point as a measure of the listener’s intrinsic spectro-temporal limitations, and assume that the SRT for any given map is affected both by the spectro-temporal contrast and by more central factors, including the ability to use linguistic knowledge and context to disambiguate a degraded signal. In support of the second hypothesis, the knee point correlated with performance on the STRIPES measure of spectro-temporal processing. An un-tested prediction is that applying a cognitive manipulation, such as requiring the listener to perform a concurrent competing task, would increase the SRT overall but not alter the knee point.

There was no effect of blurring on speech-in-noise perception when one-third of the active electrode channels were manipulated. This was an unexpected finding, especially for the most extreme conditions that used 8-fold wider analysis filters or 8 simultaneously stimulated electrodes in the 5-of-15 condition. Furthermore, experiment 2 provided no evidence that deselecting the to-be-blurred channels had an effect on speech-in-noise perception. This may lead one to the conclusion that moderate numbers of highly degraded channels do not degrade speech perception, and that there is nothing to be gained by turning them off. This conclusion should be qualified by considering the differences between our simulations of bad channels and those that occur in everyday CI use, and by the particular testing materials that we used.

The manipulations that we performed were limited to the effects of spectral blurring and some small shifts of the centre frequencies in the experimental MAPs, but did not include distortions such as those caused by cross-turn stimulation (Frijns et al. 1995; Cosentino et al. 2015a), ectopic stimulation (Finley et al. 1990), and neural dead regions (Bierer and Faulkner 2010; Cosentino et al. 2015b). These distortions manifest as place-pitch reversals (Kenway et al. 2015) or double-peaked excitation patterns, rather than the simple reduction in spectral contrast that is produced by blurring. Speech perception may also be impacted by poor temporal representation of information, as evidenced, for example, by across-electrode differences in modulation detection thresholds, rate discrimination, or gap detection (Garadat et al. 2013; Bierer et al. 2015; Cosentino et al. 2016). We do not know how robust speech perception is to these types of distortions, occurring either on all or on a subset of electrodes.

The blurring used here was applied to evenly spaced electrodes. The information conveyed by adjacent electrodes will be highly correlated, and so if (as appears to be the case) listeners can ignore degraded information on some electrodes (as in experiment 1), a more accurate representation of that information may be provided by nearby electrodes. It is likely that, if we had blurred five adjacent electrodes, particularly those driven by frequency regions that are particularly important for speech, some deficits would have been observed. We chose to space the blurred channels evenly, because most channel deselection methods impose some degree of spacing between deselected channels. It is possible that those methods would be more effective, at least after a period of acclimatization, if deactivation of adjacent electrodes were less constrained.

Finally, the speech test we used employed a masking noise based on a competing male talker. As this is one of the most difficult masker conditions for CI users, it resulted in highly positive overall SNRs for the SRTs in the SIN test for all subjects. These SRTs are higher than observed in studies with more- stationary and less-sparse maskers (e.g. Goehring et al. 2017, 2019a). Therefore, the high SNR conditions for the SIN test may have led to reduced effects of blurring than if low SNR conditions had been tested. However, the competing talker noise is characterized by sparse but highly energetic spectral components typical for speech that can strongly interfere with the target speech and this type of noise has been reported to be more sensitive to differences in spectral resolution than other types in a recent study (Croghan and Smith 2018). The reason for this can be understood by considering an input signal consisting of a tone masked by a flat-spectrum noise. Doubling the width of the analysis filter would change the signal-to-noise ratio at the output by 3 dB, but if the noise were spectrally remote from the tone then a much larger difference would occur. Nevertheless, we plan to investigate if the (lack of) effect of blurring also holds for other types of maskers that lead to lower SNR conditions for the SRTs.

Despite the above limitations and caveats, we believe that the results found with blurring have important implications for optimization strategies for CIs with relevance to channel interaction, site-selection and speech-in-noise perception. Specifically, CI listeners’ speech perception in a competing talker noise was unchanged even with extreme amounts of spectral blurring on, or the deactivation of, a moderate number of evenly spaced electrodes. This finding should be taken into account when designing strategies that aim to optimize channel interaction by manipulating a subset of electrodes that are evenly spaced along the array. Our results also suggest that deselection strategies may need to deactivate sets of adjacent electrodes, contrary to most approaches adopted so far, at least when the basis for deselection is expected to be a wider-than-average excitation pattern. Finally, the development of channel deselection strategies should consider the need to identify distortions different from those modelled here, and/or to disable more or more-closely-spaced channels.

For the goal of reducing channel interaction in CIs to achieve better outcomes, studies using blurring or similar controlled manipulations of channel interaction can lead to a better understanding of the associated effects on speech perception and inform future interventions. For example, spectral blurring or similar approaches could be used as a tool to assess individual effects of channel interaction relevant to speech perception by measuring blurring knee points as an estimate of the spectro-temporal resolution of individual listeners, independently of any cognitive effects on the overall level of performance. It could also, for example, demonstrate whether novel modes of stimulation or coding strategies improve spectro-temporal resolution.