The purpose of this study was to reveal the structural properties that need to be considered in dental implant treatment by investigating differences between dentulous and edentulous maxillae in the three-dimensional (3D) microstructure of the incisive canals (ICs) and their surrounding bone.
Methods
A total of 40 maxillary bones comprising 20 dentulous maxillae and 20 edentulous maxillae were imaged by micro-CT for 3D observation and measurement of the IC and alveolar bone in the anterior region of the IC.
Results
The Y-morphology canal was most frequently observed at 60% in dentulous maxilla and 55% in edentulous maxilla. There was a significant difference between dentulous and edentulous maxillae in IC diameter and volume, but no significant difference between the two in the major axis of the ICs.
Conclusions
The anatomic structure surrounding the IC has limited area for implant placement. Therefore, where esthetic and long-term maintenance requirements are taken into account, careful attention is needed when setting the placement position. Also, due to the resorption of bone, edentulous maxillae have a different IC morphology from dentulous maxillae, and therefore, a cautious approach is required.
Hinweise
Competing interests
Masayuki Fukuda, Satoru Matsunaga, Kento Odaka, Yuuya Oomine, Masaaki Kasahara, Masahito Yamamoto, and Shinichi Abe declare that they have no competing interests.
Authors’ contributions
MF had the discussion and analysis of incisive canals. SM participated in the design of the study and helped to draft the manuscript. KO carried out image processing. YO carried out micro-CT imaging. MK helped conduct the statistical analysis. MY participated in the bone structure analysis of the incisive canals. SA conceived the idea for the study, participated in its design and coordination, and helped draft the manuscript. All authors have read and approved the final manuscript.
Background
In recent years, with the rapid spread of dental implant treatment and a dramatic increase in accidents, the importance of precise 3D data on the human jaw is ever-increasing [1-3]. Bone resorption after tooth extraction is an unavoidable event, and the morphological features of the jawbone change greatly after tooth loss [4-7]. Moreover, the maxilla has a thinner cortical bone than the mandible and presents with a structure where cancellous bone predominates [8]. Therefore, implants have a lower survival rate than the mandible, and the search for sites suitable for implant placement has become an urgent need [9]. The position of the incisive canal (IC) is one of the most important factors for implant placement in the premaxillary region, not only in terms of survival rate but also from an esthetic point of view [10-17]. The incisive canals tend to increase in size with aging and after tooth extraction [18]. If there is a possibility of perforating the incisive canals during implant placement, then a cortical bone/cancellous bone block graft can be adapted to the incisive fossa without removing the contents of the fossa. The contents are pushed posteriorly, thus allowing proper implant placement [19].
The ICs are located in the maxillary midline posterior to the maxillary central incisors, and through them descend the nasopalatine nerve and nasopalatine artery, so they are anatomically important structures [20,21]. Mardinger et al. classified IC morphology as observed from sagittal sections into four types: cylinder-shaped, funnel-shaped, hourglass-shaped, and banana-shaped [18]. Song et al. confirmed one to four branches at the midpoint of the length of the IC and made classifications depending on the number of branches. They reported that the major type of canal shape for the IC is Y-morphology, with four other types - spindle-shaped, very large, cystic, and narrowed - existing as minor types [22]. Tolga et al. ran 2D bone measurements on the IC and surrounding bone of the IC and observed the differences between dentulous and edentulous maxillary bone [23]. Accumulating more finely detailed data directly connected to clinical practice necessitates 3D structure analysis of the bone surrounding the IC.
Anzeige
Kim et al. reported on the usefulness of micro-CT in analyzing the internal microstructure of bones [24]. 3D analysis using micro-CT, which has an imaging resolution of 5 μm at the maximum, makes it possible to reveal very complex structural properties, including even the trabecular bone.
The purpose of the present study is therefore to reveal the structural properties that need to be considered in dental implant treatment by investigating the differences in the IC and their surrounding bone structures between dentulous and edentulous maxillary bones.
Methods
Specimens
A total of 20 dentulous human maxillae and 20 edentulous maxillae samples were resected from dried adult skull bones obtained from the Department of Anatomy, Tokyo Dental College. Dentulous jaw samples with maxillary central incisors present on both sides and no midline diastema were selected to ensure they had no tooth loss.
The skull was secured to a device, and the Frankfort plane was marked with India ink; this served as the reference for cutting in parallel from the position of the zygomatic bone center to collect the sample (Figure 1).
Figure 1
Method of collecting samples. (A) The skull was secured to a device and the Frankfort plane served as a reference. (B) A cut was made at the location of the zygomatic bone center, parallel to the Frankfort plane, and the maxillary bone was detached.
×
Anzeige
Micro-CT imaging
The samples were imaged with a micro-CT system (HMX-225 Actis4; TESCO, Tokyo, Japan). Imaging conditions were as follows: matrix size 512 × 512, tube voltage 120 kV, and tube current 80 μA. The micro-CT imaging intensifier (I.I.) had a 1-in. CCD camera with a 4-in., 16-bit 1,024 × 1,024 scanning line. A total of 1,200 images of raw data were output with this camera. On the basis of this raw data, a back projection method was used to produce 2D slice data.
Region of interest
Measurement was performed by preparing three-dimensional constructed models and thereafter taking a sagittal section at the region with maximum IC diameter. The region of interest was the distance from the anterior nasal spine to the maxillary first premolar. Taken as a reference plane at the time of measurement, the virtual plane was set so as to be a plane connecting the points of the largest bulge of the left/right maxillary tuberosities and the point of the incisive foramen, parallel to the Frankfort plane.
Image processing
3D construction software (VG Studio; Volume Graphics, Heidelberg, Germany) was used to observe the internal structure of the bone by 3D construction with volume rendering from the slice data. At the same time, image processing software (Mimics; Materialise, Leuven, Belgium) was used to separate the IC and other structures, followed by reconstruction with the IC shown in red.
Classification of IC morphologies and calculation of their incidences
As the principal item, those that divided completely in two by a bony wall following the nasal septum at a point approximately one fifth to the nasal side of the nasopalatine foramina were set as Y-morphology type, and those that did not were set as cylindrical type. As a secondary item, local IC morphologies in the sagittal cross section were taken as cylinder-shaped, funnel-shaped, banana-shaped, or hourglass-shaped, in accordance with Mardinger and Mraiwa classifications [18,25]. The incidence was calculated for both the principal item and the secondary item (Figure 2).
Figure 2
Morphological variations of IC as observed from the side [18]. (1) Cylinder-shaped. (2) Funnel-shaped. (3) Banana-shaped. (4) Hourglass-shaped.
×
Measurements of surrounding bone
Measurement software (TRI-3D/BON; Ratoc System Engineering, Tokyo, Japan) was used for the following bone measurements: IC length (a), IC anterior alveolar bone height (b), IC diameter (c, d), bone width of the IC anterior alveolar bone (e1, e2, e3), and IC volume (f) (Figure 3).
Figure 3
IC measurement items. (A, C, E) CT slice images observed from the side, with sagittal sections of the IC at the middle. (B, D, F) Schematic diagrams of A, C, and E. a: IC length, distance between the midpoint of c and midpoint of d. b: Height of the anterior alveolar bone of the IC, distance to the alveolar crest from a line passing through the anterior nasal spine, in parallel with the virtual plane. c: Diameter of the nasopalatine foramina, IC diameter passing over a line connecting the anterior nasal spine and the floor of the nasal cavity, in parallel with the virtual plane. d: Diameter of the incisive foramen, maximum distance from the point (asterisk) where the superoposterior angle changes significantly. e: Width of the IC anterior alveolar bone, distance of the anterior alveolar bone parallel to the virtual plane. (e1: position of the anteroinferior point matching the diameter of the incisive foramen; e2: position of the intermediate part (asterisk); e3: position of 50% of the major axis of the upper IC). f: Total volume from c to d.
×
Statistical analysis
PASW Statistics 18 for Windows (SPSS Inc., Tokyo, Japan) was used for statistical processing. Student’s t-test was used to test for comparison between dentulous and edentulous maxillary bones. The p value was set to <0.05.
Results
Overall, 58% of all samples presented with the Y-morphology, divided completely in two by a bony wall following the nasal septum at a point approximately one fifth to the nasal side of the IC length, with two nasopalatine foramina opening on the floor of the nasal cavity. The incidence of each classification in the dentulous maxilla was as follows: 60% Y-morphology and 35% cylindrical. The corre sponding values in the edentulous maxilla were 55% and 25%. Next, the shape of the IC from the sagittal cross section was most often funnel-shaped for both dentulous and edentulous maxilla, at 50% and 45%, respectively. The cylinder-shaped was observed most frequently after the funnel-shaped morphology. Otherwise, 7.5% overall had two to four branches observed at the middle point of the length of the IC (Tables 1 and 2) (Figures 4 and 5).
Table 1
Number of individuals and proportions based on classification of the principal item
Classification of the IC from the overall appearance
Y-morphology
Cylindrical
Dentulous
n
12
7
%
60
35
Edentulous
n
11
5
%
55
25
Dentulous + edentulous
n
23
12
%
58
30
Table 2
Number of individuals and proportions based on classification of the secondary item
Classification of the IC from the sagittal cross section
Cylinder-shaped
Funnel-shaped
Banana-shaped
Hourglass-shaped
Dentulous
n
9
10
0
1
%
45
50
0
5
Edentulous
n
9
9
1
1
%
45
45
5
5
Morphologies of the classification match those in Figure 2.
Figure 4
3D image constructions of the IC in dentulous maxilla and edentulous maxilla. After imaging by micro-CT, the slice data was used for 3D construction, with the IC shown in red. IC morphology as observed from the front view was classified into Y-morphology and cylindrical [22]. (A) Y-morphology of dentulous maxilla. (B) Y-morphology of edentulous maxilla. (C) Cylindrical of dentulous maxilla. (D) Cylindrical of edentulous maxilla.
Figure 5
3D image constructions of IC showing a unique morphology. IC morphology with three or four branches was observed in one sample.
×
×
Observation of bone structure
Alveolar bone in the anterior region of the IC tended to be extremely thin on the cortical bone. In association with this, the trabecular bone structure of the alveolar process was such that in dentulous maxilla, the trabecular bone runs parallel to the longitudinal axis of the tooth and was distributed sparsely. In the edentulous maxilla, however, the arrangement of trabecular bone structure was irregular and very dense, representing a difference in bone structure characteristics (Figure 6).
Figure 6
Representative images of bone internal structure of the bone surrounding the IC. In (A-D), the 3D image constructions of dentulous maxilla and edentulous maxilla were cut in the labiopalatal direction and differences in properties pertaining to the structure of bone were observed. In (B) and (D), the samples were further sliced and observed in detail. (A, B) Relatively thick cortical bone; the cancellous bone travels in a direction parallel to the longitudinal axis of the tooth, and the density is low. (C, D) Cortical bone is especially thin in edentulous maxilla, and the cancellous bone travels with irregular arraying of fine trabecular bone. The density is very high.
×
Anzeige
Descriptive analysis of the IC and alveolar bone
The mean IC length (a) was 11.75 mm for dentulous maxilla and 10.84 mm for edentulous maxilla. The mean alveolar bone height (b) anterior to the IC was 17.97 mm for dentulous maxilla and 14.01 mm for edentulous maxilla. The mean IC diameter in (c) showed results of 2.84 mm for dentulous maxilla and 3.56 mm for edentulous maxilla; in (d), it was 4.28 mm for dentulous maxilla and 5.40 mm for edentulous maxilla. The mean bone width for IC anterior alveolar bone was 5.80 mm for dentulous maxilla and 4.06 mm for edentulous maxilla at (e1), 5.61 mm for dentulous maxilla and 5.08 mm for edentulous maxilla at (e2), and 8.45 mm for dentulous maxilla and 8.42 mm for edentulous maxilla at (e3). The mean IC volume (f) was 60.67 mm3 for dentulous maxilla and 87.05 mm3 for edentulous maxilla (Table 3).
Table 3
Comparative analysis of measurements items in dentulous maxilla and edentulous maxilla
Measurements
Dentulous (n= 20)
Edentulous (n= 20)
p
Mean ± SD
Mean ± SD
a
11.75 ± 1.70 (mm)
10.84 ± 2.42
0.241
b
17.97 ± 3.16 (mm)
14.01 ± 3.50
0.001*
c
2.84 ± 0.79 (mm)
3.56 ± 0.91
0.022*
d
4.28 ± 1.49 (mm)
5.40 ± 1.44
0.020*
e1
5.80 ± 1.21 (mm)
4.06 ± 1.77
0.002*
e2
5.61 ± 1.13 (mm)
5.08 ± 1.87
0.358
e3
8.45 ± 1.84 (mm)
8.42 ± 1.59
0.972
f
60.67 ± 36.25 (mm3)
87.05 ± 32.34
0.036*
*p < 0.05. Measurements a to f match those in Figure 3.
Discussion
Dental implant surgery in the premaxillary region often has limited bone for implant placement, and as a result, there is the risk of a poor prognosis in some instances [26]. In particular, the ICs are located in the anterior part of the hard palate, and the probability of adverse effects during implant placement in the premaxillary region is about 4% [27]. Therefore, practitioners must be aware of the risks of accidents and avoid them by using precise, detailed research data on the IC.
Close to 60% of all ICs exhibit Y-morphology. However, according to the report by Michael et al., the frequency of a cylindrical morphology of IC was 50% or more [28]. Otherwise, in terms of rare cases, Frederico et al. studied prospective implant patients using CBCT and reported that two ICs that are completely independent exist [29]. In the present study, instances where two or more IC branches existed accounted for 7.5% of the whole sample, and this suggests the possibility that they vary depending on various factors such as ethnicity or environment.
Regarding IC morphology as observed from the sagittal plane, on the other hand, funnel-shaped predominated, at 55% in dentulous maxilla and 50% in edentulous maxilla, followed by cylinder-shaped at 45% in dentulous maxilla and 45% in edentulous maxilla. This result is largely consistent with Mardinger et al.’s findings, namely, the principal shapes of the IC were shown to be funnel-shaped and cylinder-shaped, whether it be for dentulous or for edentulous maxilla. With funnel-shaped, expansion of the incisive foramen is observed, so depending on the angle of implant placement, there is a risk of perforating the IC and damaging the nasopalatine nerves and arteries. Next, the IC diameter (c, d) and volume (f) showed significant differences between dentulous and edentulous maxilla. This suggests that bone resorption due to the loss of teeth also has an impact on the IC. Bhola et al. reported that in order to obtain initial stability of the implant, there are two requisites: an implant fixture measuring 10 mm or longer must be used, and at the time of placement, there needs to be at least 3 mm or more alveolar bone from the implant body tip [30]. In the present study, where attention is limited to the alveolar bone height (b) in the anterior region of the IC, adequate bone for implant placement was present in 60% of edentulous maxilla. It is, however, desirable for there to be a thickness of 2 mm or more of hard tissue on the labial side (buccal side) of the implant, when the long-term prognosis is taken into account [31]. The mean bone width of the IC anterior alveolar bone was 4.05 mm in edentulous maxilla at e1. Considering the placement of an implant with a diameter of 4 mm, which is now commonly used, there are still comparatively many cases with high risk.
Anzeige
Typically, in implant surgery, a platform is prepared at the top of the alveolar bone [32]. However, there are reported cases where a slight gap created at the platform after placement became a space for bacteria to grow, resulting in about 1 to 2 mm of bone resorption due to inflammation of the peri-implant gingiva [33-35]. As gingival recession affects the esthetics, it seems possible that long-term prognosis could be affected by the fine cancellous bone and thin cortical bone observed in the present study.
Conclusions
The structure surrounding the IC, anatomically, has limited area for implant placement, and when esthetic and long-term maintenance requirements are taken into account, careful attention is needed in setting the placement position. Also, due to the resorption of bone, edentulous maxillae have a different IC morphology from dentulous maxillae, and therefore, a cautious approach is required.
This study demonstrated that the IC displays many morphological as well as dimensional variations. These findings may assist clinicians in understanding the morphology and planning treatment.
Acknowledgements
This study was supported by an Oral Health Science Center Grant (#5A10: Satoru Matsunaga) from Tokyo Dental College and by a Grant-in Aid for Scientific Research (no. 22791905: Satoru Matsunaga) from the Ministry of Education, Culture, Sports, Science and Technology, Japan. We thank all staff of the Department of Anatomy, Tokyo Dental College for their whole-hearted cooperation.
Anzeige
Open AccessThis article is distributed under the terms of the Creative Commons Attribution 4.0 International License (https://creativecommons.org/licenses/by/4.0), which permits use, duplication, adaptation, distribution, and reproduction in any medium or format, as long as you give appropriate credit to the original author(s) and the source, provide a link to the Creative Commons license, and indicate if changes were made.
Competing interests
Masayuki Fukuda, Satoru Matsunaga, Kento Odaka, Yuuya Oomine, Masaaki Kasahara, Masahito Yamamoto, and Shinichi Abe declare that they have no competing interests.
Authors’ contributions
MF had the discussion and analysis of incisive canals. SM participated in the design of the study and helped to draft the manuscript. KO carried out image processing. YO carried out micro-CT imaging. MK helped conduct the statistical analysis. MY participated in the bone structure analysis of the incisive canals. SA conceived the idea for the study, participated in its design and coordination, and helped draft the manuscript. All authors have read and approved the final manuscript.
Werden Personen mit Vorhofflimmern in der Blanking-Periode nach einer Katheterablation gegen eine bestehende Parodontitis behandelt, verbessert dies die Erfolgsaussichten. Dafür sprechen die Resultate einer prospektiven Untersuchung.
Bei welchen Personen eine Antibiotikaprophylaxe zur Prävention einer infektiösen Endokarditis nach invasiven zahnärztlichen Eingriffen sinnvoll ist, wird diskutiert. Neue Daten stehen im Einklang mit den europäischen Leitlinienempfehlungen.
Der Aufbau von Geweben und Organen während der Embryonalentwicklung wird von den Zellen bemerkenswert choreografiert. Für diesen Prozess braucht es spezielle sogenannte „Organisatoren“. In einer aktuellen Veröffentlichung im Fachjournal Nature Cell Biology berichten Forschende durch welchen Vorgang diese Organisatoren im Gewebe entstehen und wie sie dann die Bildung von Zähnen orchestrieren.
Infolge der Umbenennung der Deutschen Gesellschaft für Kinderzahnheilkunde in Deutsche Gesellschaft für Kinderzahnmedizin (DGKiZ) wird deren Mitgliederzeitschrift Oralprophylaxe & Kinderzahnheilkunde in Oralprophylaxe & Kinderzahnmedizin umbenannt. Aus diesem Grunde trägt die erste Ausgabe in 2024 erstmalig den neuen Titel.
Newsletter
Bestellen Sie unseren kostenlosen Newsletter Update Zahnmedizin und bleiben Sie gut informiert – ganz bequem per eMail.
