nach oben

Clinical Oral Investigations

Erschienen in:

01.06.2009 | Original Article

Effect of surface treatment on the initial bond strength of different luting cements to zirconium oxide ceramic

verfasst von: F. P. Nothdurft, P. J. Motter, P. R. Pospiech

Erschienen in: Clinical Oral Investigations | Ausgabe 2/2009

Einloggen, um Zugang zu erhalten

Abstract

The objective of this study was to compare the shear bond strength to zirconium oxide ceramic of adhesive-phosphate-monomer-containing (APM) and non-APM-containing (nAPM) luting cements after different surface treatments. nAPM cements: Bifix QM, Dual Cement, Duo Cement Plus, Multilink Automix, ParaCem Universal DC, PermaCem Smartmix, RelyX ARC, Variolink Ultra, and Variolink II; APM cements: Panavia EX, Panavia F2.0, and RelyX UniCem. Groups of ten test specimens were each prepared by layering luting cement, using cylindrical Teflon molds, onto differently treated zirconium dioxide discs. The surface treatments were airborne-particle abrasion with 110 μm alumina particles, silica coating (SC) using 30 μm alumina particles modified by silica (Rocatec System) or SC and silanization. Bifix QM and Multilink Automix were used in combination with an additional bonding/priming agent recommended by the manufacturers. After 48 h of water storage, each specimen was subjected to a shear test. Combinations involving APM-containing cements (14.41–23.88 MPa) generally exhibited higher shear bond strength than those without APM (4.29–17.34 MPa). Exceptions were Bifix QM (14.20–25.11 MPa) and Multilink Automix (19.14–23.09 MPa) in combination with system-specific silane or priming agent, which were on the upper end of shear bond strength values. With the use of the Rocatec system, a partially significant increase in shear bond strength could be achieved in nAPM cement. Modified surface treatment modalities increased the bond strength to zirconium oxide, although the most important factor in achieving a strong bond was the selection of a suitable cement. System-specific priming or bonding agents lead to further improvement.

Abo-Hamar SE, Hiller KA, Jung H, Federlin M, Friedl KH, Schmalz G (2005) Bond strength of a new universal self-adhesive resin luting cement to dentin and enamel. Clin Oral Investig 9:161–167PubMedCrossRef

Atsu SS, Kilicarslan MA, Kucukesmen HC, Aka PS (2006) Effect of zirconium-oxide ceramic surface treatments on the bond strength to adhesive resin. J Prosthet Dent 95:430–436PubMedCrossRef

Blatz MB, Chiche G, Holst S, Sadan A (2007) Influence of surface treatment and simulated aging on bond strengths of luting agents to zirconia. Quintessence Int 38:745–753PubMed

Della Bona A, Anusavice KJ, Hood JA (2002) Effect of ceramic surface treatment on tensile bond strength to a resin cement. Int J Prosthodont 15:248–253PubMed

Della Bona A, Northeast SE (1994) Shear bond strength of resin bonded ceramic after different try-in procedures. J Dent 22:103–107PubMedCrossRef

Della Bona A, van Noort R (1995) Shear vs. tensile bond strength of resin composite bonded to ceramic. J Dent Res 74:1591–1596PubMedCrossRef

Derand P, Derand T (2000) Bond strength of luting cements to zirconium oxide ceramics. Int J Prosthodont 13:131–135PubMed

Edelhoff D, Sorensen JA (2002) Retention of selected core materials to zirconia posts. Oper Dent 27:455–461PubMed

Ernst CP, Cohnen U, Stender E, Willershausen B (2005) In vitro retentive strength of zirconium oxide ceramic crowns using different luting agents. J Prosthet Dent 93:551–558PubMedCrossRef

10.

Glauser R, Sailer I, Wohlwend A, Studer S, Schibli M, Scharer P (2004) Experimental zirconia abutments for implant-supported single-tooth restorations in esthetically demanding regions: 4 year results of a prospective clinical study. Int J Prosthodont 17:285–290PubMed

11.

Janda R, Roulet JF, Wulf M, Tiller HJ (2003) A new adhesive technology for all-ceramics. Dent Mater 19:567–573PubMedCrossRef

12.

Jeong SM, Ludwig K, Kern M (2002) Investigation of the fracture resistance of three types of zirconia posts in all-ceramic post-and-core restorations. Int J Prosthodont 15:154–158PubMed

13.

Kern M, Thompson VP (1994) Sandblasting and silica coating of a glass-infiltrated alumina ceramic: volume loss, morphology, and changes in the surface composition. J Prosthet Dent 71:453–461PubMedCrossRef

14.

Kern M, Wegner SM (1998) Bonding to zirconia ceramic: adhesion methods and their durability. Dent Mater 14:64–71PubMedCrossRef

15.

Kilicarslan MA, Kedici PS, Kucukesmen HC, Uludag BC (2004) In vitro fracture resistance of posterior metal-ceramic and all-ceramic inlay-retained resin-bonded fixed partial dentures. J Prosthet Dent 92:365–370PubMedCrossRef

16.

Kim BK, Bae HE, Shim JS, Lee KW (2005) The influence of ceramic surface treatments on the tensile bond strength of composite resin to all-ceramic coping materials. J Prosthet Dent 94:357–362PubMedCrossRef

17.

Luthy H, Loeffel O, Hammerle CH (2006) Effect of thermocycling on bond strength of luting cements to zirconia ceramic. Dent Mater 22:195–200PubMedCrossRef

18.

Matinlinna JP, Heikkinen T, Ozcan M, Lassila LV, Vallittu PK (2006) Evaluation of resin adhesion to zirconia ceramic using some organosilanes. Dent Mater 22:824–831PubMedCrossRef

19.

Nicholls JI (1988) Tensile bond of resin cements to porcelain veneers. J Prosthet Dent 60:443–447PubMedCrossRef

20.

Nothdurft FP, Gernet W, Pospiech PR (2003) In vitro Untersuchungen zu vollkeramischen Stiftaufbauten aus Zirkonoxid. Dtsch Zahnärztl Z 58:451–456

21.

Nothdurft FP, Pospiech PR (2006) Clinical evaluation of pulpless teeth restored with conventionally cemented zirconia posts: a pilot study. J Prosthet Dent 95:311–314PubMedCrossRef

22.

Ozcan M, Kerkdijk S, Valandro LF (2008) Comparison of resin cement adhesion to Y-TZP ceramic following manufacturers’ instructions of the cements only. Clin Oral Investig 12:279–282PubMedCrossRef

23.

Ozcan M, Vallittu PK (2003) Effect of surface conditioning methods on the bond strength of luting cement to ceramics. Dent Mater 19:725–731PubMedCrossRef

24.

Palacios RP, Johnson GH, Phillips KM, Raigrodski AJ (2006) Retention of zirconium oxide ceramic crowns with three types of cement. J Prosthet Dent 96:104–114PubMedCrossRef

25.

Paul SJ, Werder P (2004) Clinical success of zirconium oxide posts with resin composite or glass-ceramic cores in endodontically treated teeth: a 4 year retrospective study. Int J Prosthodont 17:524–528PubMed

26.

Piwowarczyk A, Lauer HC, Sorensen JA (2005) The shear bond strength between luting cements and zirconia ceramics after two pre-treatments. Oper Dent 30:382–388PubMed

27.

Potiket N, Chiche G, Finger IM (2004) In vitro fracture strength of teeth restored with different all-ceramic crown systems. J Prosthet Dent 92:491–495PubMedCrossRef

28.

Raigrodski AJ (2004) Contemporary materials and technologies for all-ceramic fixed partial dentures: a review of the literature. J Prosthet Dent 92:557–562PubMedCrossRef

29.

Sahafi A, Peutzfeldt A, Asmussen E, Gotfredsen K (2003) Bond strength of resin cement to dentin and to surface-treated posts of titanium alloy, glass fiber, and zirconia. J Adhes Dent 5:153–162PubMed

30.

Sailer I, Feher A, Filser F, Gauckler LJ, Luthy H, Hammerle CH (2007) Five-year clinical results of zirconia frameworks for posterior fixed partial dentures. Int J Prosthodont 20:383–388PubMed

31.

Tinschert J, Natt G, Mautsch W, Augthun M, Spiekermann H (2001) Fracture resistance of lithium disilicate-, alumina-, and zirconia-based three-unit fixed partial dentures: a laboratory study. Int J Prosthodont 14:231–238PubMed

32.

Uo M, Sjogren G, Sundh A, Goto M, Watari F, Bergman M (2006) Effect of surface condition of dental zirconia ceramic (Denzir) on bonding. Dent Mater J 25:626–631PubMedCrossRef

33.

Vult von Steyern P (2005) All-ceramic fixed partial dentures. Studies on aluminum oxide- and zirconium dioxide-based ceramic systems. Swed Dent J Suppl:1–69

34.

Vult von Steyern P, Carlson P, Nilner K (2005) All-ceramic fixed partial dentures designed according to the DC-Zirkon technique. A 2 year clinical study. J Oral Rehabil 32:180–187PubMedCrossRef

35.

Vult von Steyern P, Ebbesson S, Holmgren J, Haag P, Nilner K (2006) Fracture strength of two oxide ceramic crown systems after cyclic pre-loading and thermocycling. J Oral Rehabil 33:682–689PubMedCrossRef

36.

Wegner SM, Gerdes W, Kern M (2002) Effect of different artificial aging conditions on ceramic-composite bond strength. Int J Prosthodont 15:267–272PubMed

37.

Wegner SM, Kern M (2000) Long-term resin bond strength to zirconia ceramic. J Adhes Dent 2:139–147PubMed

38.

Wolfart S, Kern M (2006) A new design for all-ceramic inlay-retained fixed partial dentures: a report of 2 cases. Quintessence Int 37:27–33PubMed

39.

Yang B, Lange-Jansen HC, Scharnberg M, Wolfart S, Ludwig K, Adelung R et al (2008) Influence of saliva contamination on zirconia ceramic bonding. Dent Mater 24:508–513PubMedCrossRef

40.

Yildirim M, Fischer H, Marx R, Edelhoff D (2003) In vivo fracture resistance of implant-supported all-ceramic restorations. J Prosthet Dent 90:325–331PubMedCrossRef

41.

Yoshida K, Kamada K, Atsuta M (1999) Adhesive primers for bonding cobalt-chromium alloy to resin. J Oral Rehabil 26:475–478PubMedCrossRef

42.

Yoshida K, Tsuo Y, Atsuta M (2006) Bonding of dual-cured resin cement to zirconia ceramic using phosphate acid ester monomer and zirconate coupler. J Biomed Mater Res B Appl Biomater 77:28–33PubMed

43.

Yoshida K, Yamashita M, Atsuta M (2004) Zirconate coupling agent for bonding resin luting cement to pure zirconium. Am J Dent 17:249–252PubMed

Titel: Effect of surface treatment on the initial bond strength of different luting cements to zirconium oxide ceramic
verfasst von: F. P. Nothdurft
P. J. Motter
P. R. Pospiech
Publikationsdatum: 01.06.2009
Verlag: Springer-Verlag
Erschienen in: Clinical Oral Investigations / Ausgabe 2/2009
Print ISSN: 1432-6981
Elektronische ISSN: 1436-3771
DOI: https://doi.org/10.1007/s00784-008-0222-8

Update Zahnmedizin

Bestellen Sie unseren kostenlosen Newsletter und bleiben Sie gut informiert – ganz bequem per eMail.

Newsletter bestellen

Live-Webinar "Urologie und Sexualmedizin in der Praxis"

Springer Medizin

Effect of surface treatment on the initial bond strength of different luting cements to zirconium oxide ceramic

Abstract

Neu im Fachgebiet Zahnmedizin

„Übersichtlicher Wegweiser“: Lauterbachs umstrittener Klinik-Atlas ist online

Klinikreform soll zehntausende Menschenleben retten

Darf man die Behandlung eines Neonazis ablehnen?

Ein Drittel der jungen Ärztinnen und Ärzte erwägt abzuwandern

Update Zahnmedizin

Live-Webinar "Urologie und Sexualmedizin in der Praxis"

Springer Medizin

Abstract

Bitte loggen Sie sich ein, um Zugang zu diesem Inhalt zu erhalten

Weitere Artikel der Ausgabe 2/2009

Clinical and microbiological effects of an essential-oil-containing mouth rinse applied in the “one-stage full-mouth disinfection” protocol—a randomized doubled-blinded preliminary study

Tooth brushing habits in uninstructed adults—frequency, technique, duration and force

Dental therapy before and after radiotherapy–an evaluation on patients with head and neck malignancies

Efficacy of denture cleansers on denture liners contaminated with Candida species

Absence of periodontitis in acromegalic patients

The impact of cement mixing and storage errors on the risk of failure of glass–ceramic crowns

Neu im Fachgebiet Zahnmedizin

„Übersichtlicher Wegweiser“: Lauterbachs umstrittener Klinik-Atlas ist online

Klinikreform soll zehntausende Menschenleben retten

Darf man die Behandlung eines Neonazis ablehnen?

Ein Drittel der jungen Ärztinnen und Ärzte erwägt abzuwandern

Update Zahnmedizin